|
PRO3 3-Series Control System®
<br />crestron.com | 800.237.2041
<br />SPECIFICATIONS
<br />Control Engine
<br />Crestron 3-Series; real-time, preemptive multi-threaded/multitasking
<br />kernel; Transaction-Safe Extended FAT file system; supports up to 10
<br />simultaneously running programs
<br />Memory
<br />SDRAM: 1 GB
<br />Flash: 4 GB
<br />Memory Card: Supports SD and SDHC cards up to 32 GB
<br />External Storage: Supports USB mass storage devices up to 1 TB
<br />Communications
<br />Ethernet: 10/100/1000 Mbps, auto-switching, auto-negotiating, auto-
<br />discovery, full/half duplex, industry-standard TCP/IP stack, UDP/IP, CIP,
<br />DHCP, SSL, TLS, SSH, SFTP (SSH File Transfer Protocol), FIPS 140-2
<br />compliant encryption, IEEE 802.1X, SNMP, BACnet/IP [2], IPv4 or IPv6,
<br />Active Directory authentication, IIS v.6.0 Web Server, SMTP e-mail client
<br />Control Subnet: 10/100/1000 Mbps Ethernet, auto-switching, auto-
<br />negotiating, auto-discovery, full/half duplex, DHCP server, DNS Server,
<br />port forwarding, Isolation Mode
<br />Cresnet: Cresnet master mode
<br />USB: Supports USB mass storage class devices via rear panel USB 2.0
<br />host port, supports computer console via front panel USB 2.0 device port
<br />RS-232/422/485: For 2-way device control and monitoring, all ports
<br />support RS-232 up to 115.2k baud with software handshaking, two ports
<br />also support hardware handshaking, RS-422, and RS-485
<br />IR/Serial: Supports 1-way device control via infrared up to 1.2 MHz or
<br />serial TTL/RS-232 (0-5 Volts) up to 115.2k baud
<br />Connectors & Card Slots
<br />S1 – S3: (3) 3-Series control card expansion slots
<br />COM 1 – 2: (2) 5-pin 3.5 mm detachable terminal blocks;
<br />Bidirectional RS-232/422/485 ports [3];
<br />Up to 115.2k baud; hardware and software handshaking support
<br />COM 3 – 6: (4) 3-pin 3.5 mm detachable terminal blocks;
<br />Bidirectional RS-232 ports [3];
<br />Up to 115.2k baud; software handshaking support
<br />IR - SERIAL OUTPUT 1 – 8: (2) 8-pin 3.5 mm detachable terminal blocks;
<br />Comprises (8) IR/Serial output ports;
<br />IR output up to 1.2 MHz;
<br />1-way serial TTL/RS-232 (0-5 Volts) up to 115.2k baud
<br />RELAY OUTPUT 1 – 8: (2) 8-pin 3.5 mm detachable terminal blocks;
<br />Comprises (8) normally open, isolated relays;
<br />Rated 1 Amp, 30 Volts AC/DC;
<br />MOV arc suppression across contacts
<br />LAN: (1) 8-pin RJ45 jack;
<br />10Base-T/100Base-TX/1000Base-T Ethernet port [3];
<br />Connects to the customer’s LAN
<br />CONTROL SUBNET: (1) 8-pin RJ45 jack;
<br />10Base-T/100Base-TX/1000Base-T Ethernet port [3];
<br />Provides a dedicated local network for Crestron devices
<br />USB: (1) USB Type A female;
<br />USB 2.0 port for storage devices
<br />MEMORY: (1) SD memory card slot;
<br />Accepts one SD or SDHC card up to 32 GB for memory expansion
<br />I/O 1 – 8: (1) 9-pin 3.5 mm detachable terminal block;
<br />Comprises (8) “Versiport” digital input/output or analog input ports
<br />(referenced to GND) [3];
<br />Digital Input: Rated for 0-24 Volts DC, input impedance 20k Ohms, logic
<br />threshold >3.125V low/0 and <1.875V high/1;
<br />Digital Output: 250 mA sink from maximum 24 Volts DC, catch diodes for
<br />use with “real world” loads;
<br />Analog Input: Rated for 0-10 Volts DC, protected to 24 Volts DC maximum,
<br />input impedance 21k Ohms with pull-up resistor disabled;
<br />Programmable 5 Volts, 2k Ohms pull-up resistor per pin
<br />NET: (1) 4-pin 3.5 mm detachable terminal block;
<br />Cresnet master port, outputs power to Cresnet devices [3];
<br />See “Power” section for additional specifications
<br />100-240V~2.4A 50/60Hz: (1) IEC 60320 C14 main power inlet;
<br />Mates with removable power cord, included
<br />G: (1) 6-32 screw;
<br />Chassis ground lug
<br />COMPUTER (front): (1) USB Type B female;
<br />USB 2.0 computer console port (6 ft cable included);
<br />For setup only
<br />LCD Display
<br />Display Type: TFT active matrix color LCD
<br />Size: 2.8 inch (72 mm) diagonal
<br />Resolution: 320 x 240 pixels
<br />Functions: Displays configuration menus, control port activity, and other
<br />system information
<br />Controls & Indicators
<br />PWR: (1) Green LED, indicates operating power supplied from AC line
<br />NET: (1) Amber LED, indicates communication with the Cresnet system
<br />MSG: (1) Red LED, indicates control system has generated an
<br />error message
<br />HW-R: (1) Recessed pushbutton for hardware reset
<br />SW-R: (1) Recessed pushbutton for software reset
<br />CNPS FAULT: (1) Red LED and (1) pushbutton, LED indicates an excessive
<br />Cresnet load detected at the NET port, pushbutton resets the
<br />fault indication
<br />SLOT 1 – 3: (3) Green LEDs, indicate control cards are inserted in the cor-
<br />responding slots
<br />Nav Pad: (1) 5-way navigation pad for menu navigation and
<br />parameter adjustment
<br />HOME: (1) Pushbutton, returns to the home menu
|