Laserfiche WebLink
L <br />ilk <br />H <br />'u <br />u. <br />I <br />I <br />0 <br />Maximum Coefficient Of Variation for Uniform Bond Stress .. ............................... 20% <br />Long Term Load (Creep): <br />(1) The rate of displacement shall decrease during the 42 day application of <br />load. <br />(2) At 42 days the total displacement due to creep (with load still applied) <br />shall be less than 0.03 inch [0.75 mm] and during the last 14 days of the 42 day load <br />duration, the total displacement due to creep shall be less than 0.003 inch [0.075 mm]. <br />(3) After removal of the 42 day load, the uniform bond Stress from a <br />subsequent Confined Tension Test shall not be less than 1,826 psi [12.6 MPa]. <br />937 -5 Product Identification (Fingerprint) Properties (FM 5 -569). <br />References for comparison including Infrared Absorption, Density or Average <br />Weight, Gel Time or Setting Time, and Bond Strength shall be determined in accordance <br />with FM 5 -569. <br />937 -6 Packaging and Marking. <br />The adhesive bonding material system shall be delivered to the project site in <br />original unopened containers with the manufacturer's label identifying the product. Each <br />package shall be clearly marked with the following information: <br />Manufacturer's name and address <br />Product Name <br />Date of Manufacture <br />Expiration Date <br />LOT Identification Number <br />Storage and Handling Requirements <br />Each package shall include the manufacturer's instructions for anchor and dowel <br />installation. The instructions shall include the following information: <br />Diameters of drilled holes for applicable anchor and dowel sizes. <br />Cleaning procedure for drilled holes, including a description of permitted and <br />prohibited equipment and techniques. <br />Allowable temperature ranges for storage, installation and curing. <br />Identification of acceptable mixing /dispensing nozzles. <br />Fabrication requirements for anchors and dowels. <br />Description of tools permitted or required for installation. <br />Method of identifying properly proportioned and mixed adhesive materials. <br />Time and temperature schedule for initial set and full- strength cure. <br />Special requirements for special installation conditions such as damp holes, <br />or horizontal or near horizontal orientation of the anchor or dowel. <br />March 2007 01000 -180 03- 4122.D ,' �" <br />' <br />Type HV <br />Type HSHV <br />Confined Tension <br />2,290 psi [15.8 MPa] <br />3,060 psi [21.1 Mpa] <br />Damp -Hole Installation <br />1,680 psi [1 1.6 MPa] <br />1,830 psi [12.6 Mpa] <br />Elevated Temperature <br />2,290 psi [15.8 MPa] <br />3,060 psi [21.1 Mpa] <br />Horizontal Orientation <br />2,060 psi [14.2 MPa] <br />2,060 psi [14.2 Mpa] <br />Short Term Cure <br />1,710 psi [1 1 .8 MPa] <br />1,710 psi [1 1 .8 Mpa] <br />Specified Bond Strength <br />1,080 psi [7.5 MPa] <br />1,830 psi [12.6 Mpa] <br />Maximum Coefficient Of Variation for Uniform Bond Stress .. ............................... 20% <br />Long Term Load (Creep): <br />(1) The rate of displacement shall decrease during the 42 day application of <br />load. <br />(2) At 42 days the total displacement due to creep (with load still applied) <br />shall be less than 0.03 inch [0.75 mm] and during the last 14 days of the 42 day load <br />duration, the total displacement due to creep shall be less than 0.003 inch [0.075 mm]. <br />(3) After removal of the 42 day load, the uniform bond Stress from a <br />subsequent Confined Tension Test shall not be less than 1,826 psi [12.6 MPa]. <br />937 -5 Product Identification (Fingerprint) Properties (FM 5 -569). <br />References for comparison including Infrared Absorption, Density or Average <br />Weight, Gel Time or Setting Time, and Bond Strength shall be determined in accordance <br />with FM 5 -569. <br />937 -6 Packaging and Marking. <br />The adhesive bonding material system shall be delivered to the project site in <br />original unopened containers with the manufacturer's label identifying the product. Each <br />package shall be clearly marked with the following information: <br />Manufacturer's name and address <br />Product Name <br />Date of Manufacture <br />Expiration Date <br />LOT Identification Number <br />Storage and Handling Requirements <br />Each package shall include the manufacturer's instructions for anchor and dowel <br />installation. The instructions shall include the following information: <br />Diameters of drilled holes for applicable anchor and dowel sizes. <br />Cleaning procedure for drilled holes, including a description of permitted and <br />prohibited equipment and techniques. <br />Allowable temperature ranges for storage, installation and curing. <br />Identification of acceptable mixing /dispensing nozzles. <br />Fabrication requirements for anchors and dowels. <br />Description of tools permitted or required for installation. <br />Method of identifying properly proportioned and mixed adhesive materials. <br />Time and temperature schedule for initial set and full- strength cure. <br />Special requirements for special installation conditions such as damp holes, <br />or horizontal or near horizontal orientation of the anchor or dowel. <br />March 2007 01000 -180 03- 4122.D ,' �" <br />' <br />