Reso 2007-1103 - Laserfiche WebLink

Home Browse Search

e I u II b t Oxidation Resistance of Pipes Pipe Location Test Method Test Conditions Requirement Liner and/or ASTM Test D. replicates (to determine 25 minutes, minimum Crown 3895) initial OJT value) Incubation Three samples for incubation Liner and /o est FM 5 -574of 195 days at 80'C and (no Average valluu e shall be less tha of 3 ± 1 minute Crown and OJT testapplied stress of 250 psi. One2 minutes) ASTM D 389501T test per each sample. 2 Note: FM= Florida Method of Test. • Required only when corrugation resin is different than liner resin. • A higher test temperature (90 °C) may be used if supporting test data acceptable to th State Materials Engineer is submitted and approved in writing. 948 -2.3.3 Certification: Furnish to the Engineer certification from the manufacturer for each pipe diameter to be incorporated into the project that the pipe meets the requirements of these Specifications. Manufacturers seeking evaluation of a product in accordance with Departmental procedures must submit test reports conducted by a laboratory deemed to be appropriately qualified by the Plastics Pipe Institute and acceptable to the State Materials Engineer. Submit this information to the Director, State Materials Office. SUBARTICLE 948 -4.4 (Page 861) is expanded by the following: 948 -4.4.1 Machine Spiral Wound Pipe Liner: Machine spiral wound pipe liner shall consist of a continuous one piece profile strip wound directly into the deteriorated pipelines. The liner can be installed in close fit to the host pipe, or alternatively installed at a fixed diameter. Where the liner is installed at a fixed diameter, the annular space between the spiral wound liner pipe and the existing pipe is grouted. (1) Polyvinyl Chloride: Polyvinyl chloride machine spiral wound pipe liner shall meet the requirements of ASTM F 1697 and shall have a minimum cell classification of 13354. March 2007 01000 -183 03- 4122.D Single Test: Test temperature 80 °C and applied stress of 650 psi.; 5calculated replicates The failure time must be equal or greater than the value using the three constants from the three points test Test temperature 80 °C and applied stresses of 650 andCalculate three constants 450 psi. Failure time at 500 psi at FM 5 -572, Test temperature 70 °C at23 °C _> 100 years (95% applied stress of 650 psi; 5statistical applied confidence) Longitudinal Procedure C, Profile* and FM 5 -573 at each stress level ASTM 2837 The failure time must be Single Test: Test temperatureequal or greater than the 80 °C and applied stress of 650 calculated value using the psi.; 5 replicates hree constants from the hree points test Oxidation Resistance of Pipes Pipe Location Test Method Test Conditions Requirement Liner and/or ASTM Test D. replicates (to determine 25 minutes, minimum Crown 3895) initial OJT value) Incubation Three samples for incubation Liner and /o est FM 5 -574of 195 days at 80'C and (no Average valluu e shall be less tha of 3 ± 1 minute Crown and OJT testapplied stress of 250 psi. One2 minutes) ASTM D 389501T test per each sample. 2 Note: FM= Florida Method of Test. • Required only when corrugation resin is different than liner resin. • A higher test temperature (90 °C) may be used if supporting test data acceptable to th State Materials Engineer is submitted and approved in writing. 948 -2.3.3 Certification: Furnish to the Engineer certification from the manufacturer for each pipe diameter to be incorporated into the project that the pipe meets the requirements of these Specifications. Manufacturers seeking evaluation of a product in accordance with Departmental procedures must submit test reports conducted by a laboratory deemed to be appropriately qualified by the Plastics Pipe Institute and acceptable to the State Materials Engineer. Submit this information to the Director, State Materials Office. SUBARTICLE 948 -4.4 (Page 861) is expanded by the following: 948 -4.4.1 Machine Spiral Wound Pipe Liner: Machine spiral wound pipe liner shall consist of a continuous one piece profile strip wound directly into the deteriorated pipelines. The liner can be installed in close fit to the host pipe, or alternatively installed at a fixed diameter. Where the liner is installed at a fixed diameter, the annular space between the spiral wound liner pipe and the existing pipe is grouted. (1) Polyvinyl Chloride: Polyvinyl chloride machine spiral wound pipe liner shall meet the requirements of ASTM F 1697 and shall have a minimum cell classification of 13354. March 2007 01000 -183 03- 4122.D