|
p" .-7,COVERAGE ere
<br /> ft2/gal (m2/L)
<br /> TAMMSCOAT SMOOTH 1st Coat 2nd Coat
<br /> Porous surfaces 80 to 100(1.96 to 2.45) 80 to 100(1.96 to 2.45) •`-1'
<br /> Smooth surfaces 80 to 120(1.96 to 2.94) 100 to 130(2.45 to 3.19)
<br /> s
<br /> : tTAMMSCOAT FINE'
<br /> +°. , Porous surfaces 50 to 65(1.23 to 1.60) 60 to 75 (1.47 to 1.84)
<br /> !Smooth.surface64 list:to 100,(1.84to 2.45): '85 to 1t0(2DB%o2.70)`. ` <- -
<br /> e '. TAMMS H/P PRIMER
<br /> Porous surfaces 100 to 150(2.45 to 3.68) -
<br /> Smooth surfaces 200 to 300(if required)(4.91 to 5.33)
<br /> TAMMS MASONRY PRIMER 40 to 80(0.98 to 1.96)
<br /> :`tom.' Note:TAMMSCOAT coverage rates are approximate and are for estimating purposes only.Surface temperature,porosity,and texture a
<br /> l
<br /> will determine actual material requirements.Apply samples to all surfaces to be coated.Obtain approval of Architect or Owner for the {",; --
<br /> '
<br /> "- color,finish,water repellency,and coverage before proceeding with work.
<br /> a
<br /> ' Surface Preparation: Cure new concrete and masonry surfaces for 28 days. Surface must be structurally •t >• )?'-n.-
<br /> :tit J.‘:... sound, clean, dry, and free of dust, dirt, oil, peeling paint, curing and form release compounds, and other
<br /> contaminants. Provide an absorptive surface on smooth pre-cast, formed concrete and other substrates by
<br /> • 1-.:,;-
<br /> e abrading the surface. Surface profile should be equal to CSP 1 to 2 in accordance with ICRI Guideline 310 2 i ^'' 1
<br /> 1^r't Defective concrete and other defects should be routed to sound material and patched using compatible ?, `l -
<br /> restoration products. Priming: For concrete and masonry, especially in hot, windy conditions, priming with ' ode
<br /> • - TAMMS H/P Primer is recommended. For highly porous concrete block, priming with TAMMS MASONRY l' t 8,
<br /> PRIMER is recommended �",.
<br /> -"' Mixing: TAMMSCOAT should be mechanically mixed using a low speed 3/4'•(19mm)drill with a mixing paddle xs=. ( °-
<br /> • ; Mix thoroughly to a uniform, smooth consistency. Do not aerate the mix. h. 'V`iv
<br /> `° Application: Spray TAMMSCOAT FINE using heavy duty spray equipment capable of spraying ceiling texture �`r tai K
<br /> ':4-1.:)::".r. S plaster or cementitious coatings. To spray TAMMSCOAT SMOOTH, use airless spray equipment with a 0 025 (�' m �s ,
<br /> to 0.035"(0.64 to 0.89 mm)orifice size spray tip.Spray TAMMSCOAT using a"cross coat"technique(horizontal -„. , ' '•
<br /> w'} r
<br /> ex r pass followed by a vertical pass).Avoid applying to excess,which can cause the product to run down the wall or r o t ,_
<br /> A I?�,j`. puddle. Backrolling is recommended during application of the first coat.The second coat can be sprayed after Y' �'
<br /> - t5, the first coat is dry,approximately 12 to 24 hours. Do not backroll during the second coat. For hand application y+.F 4- xj”
<br /> l e9it! use brushes and 11/2" (38.1 mm) nap rollers designed for latex paint. Dampen the brushes or rollers with clean _ >e'a'`
<br /> .9.1,p4,1 water before use.When using rollers,uniform millage is achieved by rolling TAMMSCOAT in one direction only. • -• tT ,g
<br /> I ;der " 'a Ail?,
<br /> '4Y >`CLEAN UP ec4 `-, _ _ c,
<br /> • nt.
<br /> Clean tools and application equipment immediately after use with soap and hot water.Clean overspray or drips r
<br /> while still wet with soap and hot water. Dried material may require strong solvents or mechanical abrasion for 5 14-la'''• r'
<br /> _ removal. 1 `
<br /> `r . PRECAUTIONS/LIMITATIONS 7' 17P
<br /> :; F- • Store at temperatures between 50°F (10°C)to 90°F (32°C). "1 y,.
<br /> • Protect from freezing. _LL e a t°�
<br /> e Co • Do not thin or dilute TAMMSCOAT. I }r> rf r. 1F{
<br /> .,4:_ • Do not apply TAMMSCOAT if rain is expected within 8 hours.
<br /> • Do not apply over frost filled surfaces. » +
<br /> ,.-ate • Do not apply if surface and ambient temperatures are below 45'F (7°C) or above 90°F (32'C). s , 4
<br /> �`.;'�•_. • Do not apply to non-absorbent materials such as glass, metal,glazed brick or glazed tile. -0,4*
<br /> • Not for use on traffic bearing surfaces. r'-44:""V
<br /> • Use HP PRIMER as a prime coat on very porous surfaces or in hot,windy conditions.
<br /> �+ -"" • In all cases,consult the Material Safety Data Sheet before use.
<br /> tt..
<br /> Rev.05.11 e x 7-T.:'`e. `
<br /> WARRANTY.The Euclid asthth=ill Company(-ErxtV)aciety and expressly warrar5 star as path= be tree from defects in motorists anwoM1T.arstip for one(1)year from the data of p base.Unless atJir¢E:
<br /> in writing by as cl:xc;of Eucy",.no other npresentabdns or.statements made by Eucla or vs representatives,in attire or aNk wall olfe,Vas warranty EUCLID MAKES NO WARRANTIES.IMPliED OR OTHERWISE
<br /> AS TO THE MERCHANTABILITY OR FITNESS FOR ORDINARY OR PARTICULAR PURPOSES OF IIS PP.(}DUCTS AND EXCLUDES THE SANE.If any Euclic pmdi h fats tc...•,...rm mar this 3 fy,Eatlio+A replace the
<br /> product at no cost to Buyer.Replacement of(thy product shall be me sole end sea.zsz.fe remedy ra^abfe and boner snail have no clam for inc tenal of emseitsr,tel damages Any xs s rd darn must be made nrmin
<br /> one(I)year"nil the data of the claimed breads.ELS does not authorize anyone on bs batna1 to maze any written of oral sa emG 5 Marco in any Way alter EucEct 5 elStarsoon 4r ita 1 a;Istats in U prod=
<br /> Ssraase or on rs pac aging Iabets..Lry irstataso of Euclid product which fads to cdr_orm van such irsatabon irdounation or i stvcm erns snob said User wesamy.Prod=demcwithmOons.if any,are done for flLslrative
<br /> purposes only&•b to rot contd.a warranty or warranty alteration of any litho.Buyer that he safely responsible for d'%TNfd the su tabSra of Eucf9's D odzeu Its to Buyers intended proposes.
<br />
|