2019-01-09_GATEWAY PARK CENTER_CONFORMED DRAWINGS FOR BID

Home Browse Search

NOTE: ALL WALL MOUNTED FACEPLATES SHALL BE MOUNTED ONTO A 4-11/16"x4-11/16"x3" DOUBLE GANG BACK BOX. EACH DOUBLE GANG BACK BOX SHALL BE FITTED WITH A SINGLE OR DOUBLE GANG PLASTER RING TO ACCEPT SINGLE OR DOUBLE GANG FACEPLATES RESPECTIVELY. INSTALL A 1-1/4" CONDUIT FROM BACK BOX TO WITHIN 6" OF THE CABLE SUPPORT SYSTEM. PROVIDE PULL STRING WITHIN ALL TELECOMMUNICATIONS CONDUITS. 1.INSTALL CONDUIT RUNS IN THE MOST DIRECT ROUTE POSSIBLE WITH NO MORE THAN TWO 90 DEGREE BENDS BETWEEN PULL POINTS OR PULL BOXES. 2.90 DEGREE CONDUITS "LB" TYPE FITTINGS SHALL NOT BE USED FOR TELECOMMUNICATIONS CABLING INSTALLATIONS. 3.CONTINUOUS CONDUIT SECTIONS OR SEGMENTS SHALL NOT BE GREATER THAN 100 LINEAR FEET IN LENGTH WITHOUT AN ADEQUATELY SIZED PULL BOX -REFER TO DETAIL 4.CONDUITS SHALL BE BONDED TO GROUND ON ONE OR BOTH ENDS IN ACCORDANCE WITH NATIONAL AND LOCAL REQUIREMENTS. 5.TELECOMMUNICATIONS CONDUITS SHALL BE INSTALLED TO WITHSTAND THE ENVIRONMENT IN WHICH THEY WILL BE EXPOSED AND IN ACCORDANCE WITH ANSI/NFPA-70; THE NATIONAL ELECTRICAL CODE. 6.THE TOTAL DISTANCE OF CONDUIT RUNS FOR TELECOMMUNICATIONS HORIZONTAL CABLE USE SHALL NOT EXCEED 150 FEET. 7.DO NOT INSTALL CONDUITS OVER OR ADJACENT TO BOILERS, INCINERATORS, HOT WATER OR STEAM LINES. 8.THE MINIMUM BEND RADIUS OF ANY PORTION OF THE CONDUIT PATHWAY SHALL BE SIX (6) TIMES THE INTERNAL DIAMETER OF THE CONDUIT FOR ALL CONDUITS 2-INCHES IN DIAMETER OR LESS. 9.THE MINIMUM BEND RADIUS OF ANY PORTION OF THE CONDUIT PATHWAY SHALL BE TEN (10) TIMES THE INTERNAL DIAMETER OF THE CONDUIT FOR ALL CONDUITS WITH AN INTERNAL DIAMETER GREATER THAN 2-INCHES. 10.WHERE A CONDUIT RUN REQUIRES A REVERSE BEND (BETWEEN 100 DEGREES AND 180 DEGREES) A PULL BOX SHALL BE INSTALLED AT EACH BEND HAVING SUCH ANGLE, WITHIN 10 FEET OF THE BEND. 11.IF A CONDUIT RUN REQUIRES A THIRD 90 DEGREE BEND BETWEEN PULL POINTS OR PULL BOX, THE OVERALL DESIGN CAPACITY OF THE CONDUIT SYSTEM SHALL HAVE A DERATED TOTAL CAPACITY OF 15 PERCENT. 12.ALL CONDUIT ENDS SHALL BE REAMED AND FITTED WITH THREADED INSULATING BUSHING TO ELIMINATE SHARP EDGES THAT CAN DAMAGE CABLES DURING INSTALLATION. 13.CONDUITS THAT PROTRUDE THROUGH WALLS AND FLOORS SHALL BE EXTENDED BEYOND THE SURFACE PENETRATION TO WITHIN 12 INCHES OF THE CABLE TRAY OR CABLE RUNWAY SYSTEM. 14.ALL TELECOMMUNICATION OUTLETS STUB-UPS SHALL BE EQUIPPED WITH A PULL STRING WITH A MINIMUM TEST RATING OF 200 LBS. 15.ALL INTERIOR COMMUNICATIONS CONDUITS GREATER THAN 1 1/2" CONDUITS SHALL BE EQUIPPED WITH 1/2" CABLE PULL STRING WITH 1250 LBS OF TENSILE STRENGTH AND SEQUENTIAL FOOTAGE MARKING. 16.ALL EXTERIOR COMMUNICATIONS CONDUITS SHALL BE EQUIPPED WITH 1/2" CABLE PULL STRING WITH 1250 LBS OF TENSILE STRENGTH AND SEQUENTIAL FOOTAGE MARKING. 17.INSTALL PULL BOXES IN ACCESSIBLE LOCATIONS. DIRECT ACCESS TO PULL BOXES IS REQUIRED. PROVIDE LABELED, HINGED ACCESS PANEL DOOR. PULL BOXES SHALL BE LISTED FOR THE PURPOSE. 18.THE MINIMUM LENGTH OF PULL BOX SHALL BE 12 TIMES THE DIAMETER OF THE LARGEST CONDUIT. PULL BOXES SHALL NOT BE USED IN SUBSTITUTION OF A 90 DEGREE BEND. 19.REFER TO ARCHITECTURAL DRAWINGS FOR MOUNTING ELEVATIONS. 20.REFER TO ARCHITECTURAL REFLECTED CEILING PLANS FOR COORDINATION OF ALL CONDUIT, RUNWAY, AND TRAY. 21.COORDINATE EXACT LOCATIONS OF ALL FLOOR BOXES AND POKE-THRU DEVICES WITH ARCHITECT PRIOR TO INSTALLATION. 22.ALL OUTLET LOCATIONS AND DIMENSIONS ARE APPROXIMATE. COORDINATE EXACT MOUNTING LOCATION AND HEIGHT WITH ARCHITECTURAL DRAWINGS PRIOR TO INSTALLATION. 23.WHERE CABLE TRAY RUNS ARE OBSTRUCTED, J-HOOKS MAY BE USED. J-HOOKS SHALL BE SPACED NO LESS THAN 48" O.C AND NOT GREATER THAN 60" O.C. WHERE COMMUNICATIONS CABLE AND SECURITY CABLE FOLLOW THE SAME PATH, CABLES SHALL BE SEPARATED. ALL TELECOMMUNICATION OUTLETS SHOWN IN OPEN AIR ENVIRONMENT (I.E. MECHANICAL SPACE, PENTHOUSE, ROOF, GARAGE) SHALL BE INSTALLED IN CONDUIT, RATED FOR THAT ENVIRONMENT. 24.ALL TELECOMMUNICATIONS HORIZONTAL STRUCTURED CABLING SHALL BE INSTALLED IN MAIN AND SECONDARY CORRIDORS ONLY FROM TELECOMMUNICATIONS ROOM TO WORK AREA OUTLETS. 25.ALL TELECOMMUNICATIONS HORIZONTAL STRUCTURED CABLING SHALL ENTER WORK AREA ROOMS VIA PROPERLY SIZED CONDUIT ABOVE DOOR. CONDUIT SLEEVE SHALL BE PROPERLY FIRESTOPPED TO MAINTAIN FIRE RATING. 26.UNDER NO CIRCUMSTANCES SHALL TELECOMMUNICATIONS HORIZONTAL STRUCTURED CABLING BE INSTALLED THROUGH ADJACENT ROOMS TO WORK AREA OUTLETS. 4 1 COMMUNICATIONS LEGEND GENERAL PATHWAY REQUIREMENTS POI POINT OF INTERFACE POTS PLAIN OLD TELEPHONE SERVICE PR PAIR PTSS PASSIVE TRANSMISSION SUBSYSTEM PVC POLYVINYL CHLORIDE SE SERVICE ENTRANCE SER SATELLITE EQUIPMENT ROOM SI SYSTEM INTERNATIONAL SL SLEEVE SMPS SWITCHED MODE POWER SUPPLY SNA SYSTEMS NETWORK ARCHITECTURE SP SERVICE PROVIDER SPC STORED PROGRAM CONTROL SPD SURGE PROTECTION DEVICE SPG SINGLE-POINT GROUND STA STATION STP SHIELDED TWISTED PAIR SW STATION WIRE SWB SWITCHBOARD SYS SYSTEM TB TERMINAL BLOCK TBBC TELECOMMUNICATIONS BACKBONE BONDING CONDUCTOR TBC TELECOMMUNICATION BONDING CONDUCTOR TC TELECOMMUNICATIONS CLOSET TDM TIME DIVISION MULTIPLEXING TEBC TELECOMMUNICATIONS EQUIPMENT BONDING CONDUCTOR TEL TELEPHONE TELCO TELEPHONE COMPANY TERM TERMINAL TGB TELECOMMUNICATIONS GROUNDING BUSBAR THD TOTAL HARMONIC DISTORTION TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION TM TRANSFORMER MAINTENANCE HOLE TMGB TELECOMMUNICATIONS MAIN GROUNDING BUSBAR TO TELECOMMUNICATIONS OUTLET TPDDI TWISTED PAIR DISTRIBUTED DATA INTERFACE TPPMD TWISTED PAIR PHYSICAL MEDIUA DEPENDENT TR TELECOMMUNICATIONS ROOM TSB TELECOMMUNICATIONS SYSTEM BULLETIN TT TELEPHONE TERMINAL TTB TELEPHONE TERMINAL BOARD TTY TEXT TELEPHONES TVSS TRANSIENT VOLTAGE SURGE SUPPRESSOR TYP TYPICAL UG UNDERGROUND UL UNDERWRITERS LABORATORIES UPS UNINTERRUPTIBLE POWER SUPPLY UTP UNSHIELDED TWISTED PAIR ISDN INTEGRATED SERVICES DIGITAL NETWORK ISO INTEGRATED STANDARDS ORGANIZARION IW INSIDE WIRING (CABLE) KHz KILOHERTZ KTS KEY TELEPHONE SYSTEM LAN LOCAL AREA NETWORK LASER LIGHT AMPLIFICATION BY STIMULATED EMISSION OF RADIATION LATA LOCAL ACCESS TRANSPORT AREA LBO LINE BUILDOUT LEC LOCAL EXCHANGE CARRIER LED LIGHT EMITTING DIODE LOCAP LOW CAPACITANCE MAP MANUFACTURING AUTOMATION/PROTOCOL MAX MAXIMUM MC MAIN CROSS-CONNECT MDF MAIN DISTRIBUTION FRAME M/G MOTOR/GENERATOR SET MH MAINTENANCE HOLE MICRON MICROMETER MIN MINIMUM MISC MISCELLANEOUS MODEM MODULATOR/DEMODULATOR MPOP MINIMUM POINT OF PRESENCE MTT MAIN TELEPHONE TERMINAL N NEWTON NEC NATIONAL ELECTRIC CODE NESC NATIONAL ELECTRIC SAFETY CODE NI NETWORK INTERFACE NIC NOT IN CONTRACT NID NETWORK INTERFACE DEVICE NIU NETWORK INTERFACE UNIT NRTL NATIONALLY RECOGNIZED TESTING LABORATORY NTS NOT TO SCALE OC ON CENTER OD OUTSIDE DIAMETER OFNP OPTICAL FIBER NON-CONDUCTIVE PLENUM OFNR OPTICAL FIBER NON-CONDUCTIVE RISER OPD OVERCURRENT PROTECTION DEVICE OPE OUTSIDE PLANT ENGINEER OSHA OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION OSP OUTSIDE PLANT PAM PULSE AMPLITUDE MODULATE PB PULL BOX PBX PRIVATE BRANCH EXCHANGE PCM PULSE CODE MODULATION PIC POLYETHYLENE INSULATED CONDUCTOR PL PRIVATE LINES PLT PLANT PM PHASE MODULATION D/A DIGITAL TO ANALOG CONVERSION DAF DEDICATED ACCESS FACILITY DB DECIBEL DC DIRECTED CURRENT DCE DATA CIRCUIT-TERMINATION EQUIPMENT DCO DIGITAL CENTRAL OFFICE DD DISTRIBUTION DESIGNER DEMARC DEMARCATION POINT DGM DATA GRADE MEDIUM DTE DATA TERMINAL EQUIPMENT DW DISTRIBUTION WIRE DWG DRAWING(S) EBC EQUIPMENT BONDING CONDUCTOR EC ELECTRICAL CONTRACTOR EF ENTRANCE FACILITY EIA ELECTRONICS INDUSTRY ASSOCIATION ELEC ELECTRICAL EMC ELECTROMAGNETIC COMPATABILITY EMI ELECTROMAGNETIC INTERFACE EMR ELECTROMAGNETIC RADIATION EMT ELECTRICAL METALLIC TUBING ESS ELECTRONIC SWITCHING SYSTEM ETV EDUCATIONAL TELEVISION E/W EQUIPPED WITH EXCH EXCHANGE EXT EXTENSION FCC FEDERAL COMMUNICATIONS COMMISSION FD FLOOR DISTRIBUTION FDDI FIBER DISTRIBUTION DATA INTERFACE FDM FREQUENCY DIVISION MULTIPLEXING FDR FEEDER FO FIBER OPTIC FOTP FIBER OPTIC TRANSMISSION SYSTEM FREQ FREQUENCY FTP FOIL TWISTED PAIR GA GAUGE GEC GROUNDING ELECTRIC CONDUCTOR GHz GIGAHERTZ GND GROUND HC HORIZONTAL CROSS-CONNECT HF HIGH FREQUENCY HH HANDHOLE HVAC HEATING, VENTILATION AND AIR CONDITIONING Hz HERTZ IC INTERMEDIATE CROSS-CONNECT ICEA INSULATED CABLE ENGINEERS ASSOCIATION IDC INSULATION DISPLACEMENT CONNECTION IDF INTERMEDIATE DISTRIBUTION FRAME IEEE INTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS 8P8C 8-POSITION, 8-CONDUCTOR AC ALTERNATING CURRENT A/D ANALOG TO DIGITAL CONVERSION ACO ANALOG CENTRAL OFFICE ADA AMERICANS WITH DISABILITIES ACT ADO AUXILIARY DISCONNECT OUTLET AER AERIAL AFF ABOVE FINISHED FLOOR AIA AMERICAN INSTITUTE OF ARCHITECTS AM AMPLITUDE MODULATION ANSI AMERICAN NATIONAL STANDARDS INSTITUTE ARMM PIC RISER, EXPANDED POLYETHYLENE PVC, 24 AWG, ALVYN ASCII AMERICAN STANDARD CODE FOR INFORMATION INTERCHANGE ATM ASYNCHRONOUS TRANSFER MODE AWG AMERICAN WIRE GAUGE B BURIED BC BONDING CONDUCTOR BBISDN BROADBAND INTEGRATED SERVICES DIGITAL NETWORK BD BUILDING DISTRIBUTOR BDF BUILDING DISTRIBUTION FRAME BEF BUILDING ENTRANCE FACILITY BER BIT ERROR RATE BIC BUILDING INDUSTRY CONSULTANT BICSI BUILDING INDUSTRY CONSULTING SERVICES BRISDN BASIC RATE INTEGRATED SERVICES DIGITAL NETWORK BTU BRITISH THERMAL UNIT CA CABLE CATV CABLE TELEVISION CBC COUPLED BONDING CONDUCTOR CC COMMUNICATIONS CONTRACTOR CCITT THE INTERNATIONAL TELEGRAPH AND TELEPHONE CONSULTATIVE COMMITTEE CD CONDUIT CDDI COPPER DISTRIBUTED DATA INTERFACE CDF COPPER DISTRIBUTION FRAME CDO COMMUNITY DIAL OFFICE CER COMPUTER EQUIPMENT ROOM CIRC CIRCUIT CFC COMMUNICATIONS FLAT CABLE CLO CLOSET CO CENTRAL OFFICE CODEC CODER/DECODER COE CENTRAL OFFICE EQUIPMENT COT CENTRAL OFFICE TERMINAL CPC CUSTOMER PREMISES COMMUNICATIONS CPE CUSTOMER PREMISES EQUIPMENT CPU CENTRAL PROCESSING UNIT CSA CANADIAN STANDARDS ASSOCIATION CSMA/CA CARRIER SENSE MULTIPLE ACCESS/COLLISION AVOIDANCE CSMA/CD CARRIER SENSE MULTIPLE ACCESS/COLLISION DETECTION GENERAL TELECOMMUNICATIONS LEGEND STANDARD 1-PORT TELECOMMUNICATIONS OUTLET. INSTALL (1) 8P8C MODULAR JACK INSERT INTO (1) 2-PORT SINGLE GANG FACEPLATE. INSTALL (1) DEDICATED UTP CATEGORY CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. INSTALL BLANK INSERTS IN ALL UNUSED PORTS. COORDINATE MOUNTING HEIGHT WITH ARCHITECTURAL DRAWINGS PRIOR TO ROUGH-IN. REFER TO COMMUNICATIONS DETAILS FOR MORE INFORMATION. STANDARD 2-PORT TELECOMMUNICATIONS OUTLET. INSTALL (2) 8P8C MODULAR JACK INSERTS INTO (1) 2-PORT SINGLE GANG FACEPLATE. INSTALL (1) DEDICATED UTP CATEGORY CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. COORDINATE MOUNTING HEIGHT WITH ARCHITECTURAL DRAWINGS PRIOR TO ROUGH-IN. REFER TO COMMUNICATIONS DETAILS FOR MORE INFORMATION. STANDARD 4-PORT TELECOMMUNICATIONS OUTLET. INSTALL (4) 8P8C MODULAR JACK INSERTS INTO (1) 4-PORT SINGLE GANG FACEPLATE. INSTALL (1) DEDICATED UTP CATEGORY CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. COORDINATE MOUNTING HEIGHT WITH ARCHITECTURAL DRAWINGS PRIOR TO ROUGH-IN. REFER TO COMMUNICATIONS DETAILS FOR MORE INFORMATION. 2 TV FF 2 IPC WL FB2 FB4 STANDARD 2-PORT CATV OUTLET. INSTALL (1) 8P8C MODULAR JACK INSERT AND (1) F-CONNECTOR INSERT INTO (1) 2-PORT SINGLE GANG FACEPLATE. INSTALL (1) DEDICATED UTP CATEGORY CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. INSTALL (1)RG-6 CABLE FOR EACH F-CONNECTOR INSERT INSTALLED. COORDINATE MOUNTING HEIGHT WITH ARCHITECTURAL DRAWINGS PRIOR TO ROUGH-IN. REFER TO COMMUNICATIONS DETAILS FOR MORE INFORMATION. WALL MOUNTED FURNITURE FEED. PROVIDE (2) 1-1/4" CONDUITS FROM WALL MOUNTED BOX TO CABLE SUPPORT SYSTEM. PROVIDE FLEXIBLE TECHFLEX NYLON BRAIDING SLEEVE MATERIAL FROM THE COVER PLATE TO FURNITURE ACCESS LOCATION. STANDARD 2-PORT CEILING MOUNTED TELECOMMUNICATIONS OUTLET. INSTALL (2) 8P8C MODULAR JACK INSERTS INTO (1) 4-PORT SINGLE GANG FACEPLATE MOUNTED ON BACKBOX. INSTALL (1) DEDICATED UTP CATEGORY CABLE FOR EACH 8P8C MODULAR JACK INSTALLED. TERMINATE ALL 8 CONDUCTORS. COORDINATE MOUNTING LOCATION WITH ARCHITECTURAL DRAWINGS PRIOR TO ROUGH-IN. REFER TO COMMUNICATIONS DETAILS FOR MORE INFORMATION. STANDARD 1-PORT CEILING MOUNTED IP CAMERA OUTLET. INSTALL (1) 8P8C MODULAR JACK INSERTS INTO (1) 2-PORT SURFACE MOUNTED DEVICE BOX MOUNTED IN BACKBOX. INSTALL (1) DEDICATED UTP CATEGORY CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. INSTALL BLANK INSERT IN ALL UNUSED PORTS. COORDINATE MOUNTING LOCATION WITH ARCHITECTURAL DRAWINGS PRIOR TO ROUGH-IN. REFER TO COMMUNICATIONS DETAILS FOR MORE INFORMATION. STANDARD 2-PORT CEILING MOUNTED WIRELESS ACCESS POINT OUTLET. INSTALL (2) 8P8C MODULAR JACK INSERTS INTO (1) 2-PORT SURFACE MOUNTED DEVICE BOX WITHIN WIRELESS ACCESS POINT ENCLOSURE. INSTALL (1) DEDICATED UTP CATEGORY CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. COORDINATE MOUNTING LOCATION WITH ARCHITECTURAL DRAWINGS PRIOR TO ROUGH-IN. REFER TO COMMUNICATIONS DETAILS FOR MORE INFORMATION. STANDARD PATHWAY OUTLET. PROVIDE (1) 1" CONDUIT WITH 4-11/16" X 4-11/16" X 3" DEEP BACKBOX WITH 1G DEVICE PLATE STUBBED ABOVE ACCESSIBLE CEILING. COORDINATE MOUNTING HEIGHT WITH ARCHITECTURAL DRAWINGS PRIOR TO ROUGH-IN. REFER TO COMMUNICATIONS DETAILS FOR MORE INFORMATION. STANDARD 2-PORT FLOOR BOX TELECOMMUNICATIONS OUTLET. INSTALL (2) 8P8C MODULAR JACK INSERTS INTO (1) 2-PORT MOUNTING BRACKET IN DESIGNATED FLOORBOX LOCATION. INSTALL (1) DEDICATED UTP CATEGORY CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. COORDINATE FINAL LOCATION WITH ARCHITECTURAL DIMENSIONED DRAWINGS PRIOR TO ROUGH-IN. REFER TO ELECTRICAL DRAWINGS FOR MORE INFORMATION. TELECOMMUNICATIONS CONTRACTOR TO PROVIDE MOUNTING BRACKET AND BEZEL IN FLOOR BOX DEVICE PROVIDED BY ELECTRICAL CONTRACTOR. COORDINATE IN FIELD. STANDARD 4-PORT FLOOR BOX TELECOMMUNICATIONS OUTLET. INSTALL (4) 8P8C MODULAR JACK INSERTS INTO (1) 4-PORT MOUNTING BRACKET IN DESIGNATED FLOORBOX LOCATION. INSTALL (1) DEDICATED UTP CATEGORY CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. COORDINATE FINAL LOCATION WITH ARCHITECTURAL DIMENSIONED DRAWINGS PRIOR TO ROUGH-IN. REFER TO ELECTRICAL DRAWINGS FOR MORE INFORMATION. TELECOMMUNICATIONS CONTRACTOR TO PROVIDE MOUNTING BRACKET AND BEZEL IN FLOOR BOX DEVICE PROVIDED BY ELECTRICAL CONTRACTOR. COORDINATE IN FIELD. FF PT FLOOR MOUNTED FURNITURE FEED, POKE THRU. PROVIDE (1) 2" CONDUIT TO CABLE SUPPORT SYSTEM OF FLOOR BEING SERVED. CABLING SHOULD NOT BE RUN IN CABLE SUPPORT SYSTEM ON FLOOR BELOW. PROVIDE FLEXIBLE TECHFLEX NYLON BRAIDING SLEEVE MATERIAL FROM THE COVER PLATE TO FURNITURE ACCESS LOCATION. GENERAL DEMOLITION NOTES: 1.REFER TO ARCHITECTURAL DRAWINGS FOR THE FULL EXTENT OF THE SCOPE OF WORK. THE TECHNOLOGY SCOPE OF WORK MAY EXTEND BEYOND THE AREA DEFINED BY THE ARCHITECTURAL DEMOLITION PLANS TO FULLY COMPLY WITH VARIOUS REQUIREMENTS DEFINED BY THESE NOTES. 2.THE TECHNOLOGY DEMOLITION PLANS INDICATE THE GENERAL INTENT AND ARE NOT INTENDED TO SHOW ALL ITEMS TO BE REMOVED OR RETAINED. THE TECHNOLOGY CONTRACTOR SHALL VISIT THE SITE PRIOR TO THE SUBMISSION OF BIDS TO BECOME FAMILIAR WITH THE ACTUAL CONDITIONS AND EXTENT OF WORK. DEVICES AND EQUIPMENT LOCATED ON THE WALL AND/OR CEILING TO BE REMOVED SHALL BE DISCONNECTED AND MADE SAFE. THE TECHNOLOGY CONTRACTOR SHALL NOTIFY THE OWNER'S REPRESENTATIVE OF ANY UNANTICIPATED HIDDEN CONDITIONS ENCOUNTERED DURING DEMOLITION. 3.THE TECHNOLOGY CONTRACTOR SHALL BE RESPONSIBLE FOR THE REPAIR OF ALL SYSTEMS OR BUILDING COMPONENTS DAMAGED DURING THE EXECUTION OF THE WORK. DAMAGE SHALL INCLUDE BUT NOT BE LIMITED TO DESTRUCTION OR DISPOSAL OF ITEMS INTENDED TO REMAIN OR TO BE SALVAGED. 4.THE TECHNOLOGY CONTRACTOR SHALL TRACE AND LABEL ALL EXISTING CABLING WITHIN THE AREA OF DEMOLITION SCOPE OF WORK PRIOR TO DISCONNECTION. 5.THE TECHNOLOGY CONTRACTOR SHALL IDENTIFY ALL CABLING AND SYSTEM COMPONENTS WHICH ARE TO REMAIN WITHIN THE AREA OF DEMOLITION SCOPE. THERE SHALL BE NO INTERRUPTION OF SERVICE TO ANY AREA OUTSIDE THE SCOPE LIMITS WITHOUT APPROVAL FROM THE OWNER'S REPRESENTATIVE. EXISTING EQUIPMENT TO REMAIN SHALL BE LEFT IN A CODE COMPLIANT MANNER. 6.THE TECHNOLOGY CONTRACTOR SHALL REMOVE ALL CABLING AND RACEWAYS TO THEIR POINTS OF ORIGIN WITHIN THE AREA OF DEMOLITION SCOPE. ITEMS IDENTIFIED FOR DEMOLITION SHALL NOT BE ABANDONED IN PLACE. RACEWAY THAT ENTER MASONRY WALLS OR FLOORS SHALL BE CUT FLUSH AT THE SURFACE FOR PATCHING BY OTHERS. 7.THE TECHNOLOGY CONTRACTOR SHALL TEMPORARILY SUPPORT ALL LOW VOLTAGE CABLING AND ASSOCIATED ITEMS TO REMAIN THAT ARE AFFECTED BY DEMOLITION OF THE BUILDING STRUCTURAL COMPONENTS (WALL, CEILINGS, ETC.) TEMPORARY SUPPORTED ITEMS SHALL BE PERMANENTLY SUPPORTED AND INSTALLED WHEN FINALIZED STRUCTURES ARE IN PLACE. 8.ALL REMOVED ITEMS SHALL BE LEGALLY DISPOSED OF UNLESS IDENTIFIED FOR USE. THE OWNER'S REPRESENTATIVE SHALL INSPECT ALL RETAINED ITEMS PRIOR TO PLACEMENT IN THE IDENTIFIED STORAGE LOCATION BY TECHNOLOGY CONTRACTOR. 9.COORDINATE WITH GENERAL, MECHANICAL, PLUMBING, AND ELECTRICAL CONTRACTORS FOR EXISTING EQUIPMENT TO BE REMOVED. DISCONNECT AND REMOVE ANY TECHNOLOGY DEVICES PRIOR TO EQUIPMENT BEING REMOVED. 10.THE CONTRACTOR SHALL PROVIDE BLANK METAL PLATES FOR ALL JUNCTION/DEVICE BOXES NO LONGER IN USE. 11.ALL DEMOLITION AND CONSTRUCTION ACTIVITIES SHALL BE COORDINATED WITH THE GENERAL CONTRACTOR TO MINIMIZE DISRUPTION TO THE NORMAL DAILY FUNCTIONING OF THE OCCUPIED. 12.ALL NON-ATTACHED ITEMS, SUCH AS MOBILE EQUIPMENT, DESKTOP PC OR PHONES SHALL BE REMOVED BY OWNER PRIOR TO COMMENCEMENT OF DEMOLITION WORK. 13.UPON COMPLETION, CLEAN ALL AREAS AND REMOVE ALL DEMOLITION MATERIALS, CLEAN ALL ADJACENT AREA AFFECTED BY DEMOLITION. 14.ALL NETWORK EQUIPMENT AND WIRELESS ACCESS POINTS SHALL BE REMOVED BY OWNER PRIOR TO COMMENCEMENT OF DEMOLITION WORK. DEMOLITION KEYNOTES: REMOVE ALL EXISTING NURSE CALL DEVICES WITHIN THE LIMIT OF WORK COMPLETELY BACK TO THE POINT OF ORIGIN. CABLING AND RACEWAY TO BE DISPOSED OF PROPERLY. NURSE CALL DEVICES, CONTROLLERS, POWER SUPPLIES ARE TO BE TURNED OVER TO OWNER. DECOMMISSION OR BY-PASS ALL NURSE CALL DEVICES TO BE REMOVED PRIOR TO COMMENCEMENT OF WORK. 1 REMOVE ALL EXISTING OVERHEAD PAGING SYSTEMS WITHIN THE LIMIT OF WORK BACK TO THE LOCAL PAGING EQUIPMENT HEAD-END. SPEAKERS, BACK BOXES, CABLING AND RACEWAY TO BE DISPOSED OF PROPERLY. COORDINATE EXISTING PAGING SYSTEM WITH OWNER STAFF TO MAINTAIN PAGING FEED, CABLE OR CONNECTING PAGING ZONES. 2 REMOVE ALL EXISTING TELECOMMUNICATIONS, SECURITY, VIDEO SURVEILLANCE AND INTERCOM DEVICES WITHIN THE LIMIT OF WORK COMPLETELY BACK TO POINT OF ORIGIN. CABLING AND RACEWAY TO BE DISPOSED OF PROPERLY. EXISTING PATCH PANELS TO BE REMOVED FROM EXISTING COMMUNICATIONS ROOMS ARE TO BE TURNED OVER TO THE OWNER AT A LOCATION DESIGNATED BY OWNER. REFER TO ARCHITECTURAL DEMOLITION PLANS FOR EXACT SCOPE OF WORK TO BE DEMOLISHED. 3 EXISTING DAS INSTALLATION SHALL BE REMOVED/REPLACED BY OWNERS DAS INSTALLATION VENDOR. COORDINATE WITH OWNER PRIOR TO START OF WORK. 4 THE TELECOMMUNICATIONS CONTRACTOR SHALL COORDINATE TEMPORARY REMOVAL OF ALL CEILING MOUNTED TECHNOLOGY DEVICES WITHIN THE AREA OF WORK WHERE REQUIRED FOR ANY CEILING REMOVAL. UPON COMPLETION OF ABOVE CEILING WORK, REINSTALL AND RECONNECT DEVICES AS REQUIRED BACK TO CURRENT CONDITION. 5 STANDARD ROOM SCHEDULER OUTLET. INSTALL (2) 8P8C MODULAR JACK INSERTS INTO (1) 2-PORT SINGLE GANG FACEPLATE. INSTALL (1) DEDICATED UTP CATEGORY CABLE FOR EACH 8P8C MODULAR JACK INSERT INSTALLED. TERMINATE ALL 8 CONDUCTORS. COORDINATE MOUNTING HEIGHT WITH ARCHITECTURAL DRAWINGS PRIOR TO ROUGH-IN. REFER TO COMMUNICATIONS DETAILS FOR MORE INFORMATION. RS 1423 A C B 1423 A C SHEET NUMBER TITLE Approved Checked Drawn Job Number ISSUE CHART CONSULTANTS KEYPLAN PROJECT B FIRM CERTIFICATION C.A #6057 ERIK S WALKER P.E: #63929 JOHN MOUDLER P.E: #33200 CARLOS E. JIMENEZ P.E: #47923 RICARDO DURAN P.E: #64768 GLEN R. SEILER P.E: #83347 BR+A CONSULTING ENGINEERS 2600 DOUGLAS ROAD, SUITE 1100 CORAL GABLES, FL 33134 THORNTON TOMASETTI 101 NE THIRD AVENUE, SUITE 1170 FORT LAUDERDALE, FL 3330` f.954.903.9300 f 954.903 9301 ESI CONSULTING ENGINEERS, INC 1315 NW 98TH CT. UNIT 15, DORAL, FL 33172 t. 305.418.9177 t 305.418.9178 HVAC STRUCTURAL ENGINEERS ELECTRICAL + PLUMBING INMAN FOODSERICE GROUP 1330 CORAL WAY SUITE 310 MIAMI, FL 33145 FOOD SERVICE PE R M I T S E T 1 2 . 0 6 . 1 8 1 2 /4 /2 0 1 8 8 :0 7 :4 9 A M C :\_R e v i t \T E C H - G A T E W A Y - v 2 0 1 8 _a v i l l a n u e v a C B Y X V .r v t T00-01 COMMUNICATIONS LEGEND JJP AMV 810495.000 JJP SIB -GATEWAY PARK Copyright © 2018 Perkins+Will PROJECT ADDRESS: 151 Sunny Isles Blvd Sunny Isles Beach, FL 33160 2800 Ponce De Leon Blvd Suite 1300 Coral Gables, FL 33134 t 305.569.1333 f 305.569.1334 www.perkinswill.com NO.ISSUE DATE PERMIT SET 12.06.2018