Ric-Man International Inc. - Laserfiche WebLink

Home Browse Search

on intormatlon S):1 Information and Instruction (For Information Only) Sales Representative - Construction Superintendent - SPENCER DALMAN Project Manager - Package Information Description Type nformation and Instruction / Approval Selection For Approval - Signature required lain Elevator Layout For Approval - Signature required Entrance Detail Drawing For Approval - Signature required Remarks: • The enclosed submittals are in compliance with conditions of ThyssenKrupp Elevator's Subcontract for supplying and installing material and /or systems for the project referenced above. • This Elevator installation is an integral design. Due to this nature, no equipment can be released to fabrication without all appropriate approvals and confirmations. • "Approvals" must contain inclusive confirmations as stated in the section titled "Remittance Instructions" • Failure to provide and approve this information in a timely manner may result in a delay of elevator fabrication and delivery to job site. Remittance Instructions Please remit at least 2 copies of all confirmations and approvals to: Office Location: ThyssenKrupp Elevator Attn: 7481 NW 66 ST., MIAMI, FL 33166 Phone: 800 - 683 -8888 Fax: 866 - 248 -8924 ThyssenKrupp will not release any elevator marterial for fabrication without the following information, in addition to a fully executed subcontract agreement. • Please review the elevator layouts and detail drawings closely. Check ALL hoistway dimensions, elevator travel ( floor to floor heights), pit depth, clear over -head, machine room dimensions, and entrance wall thickness. Mark -up the drawings accordingly, and remit with neccessary approval (i.e.: approval or approved as noted) to the Local ThyssenKrupp Office shown above. • Enclosed drawings are for approval purposes only and not to be used for construction. • Please confirm finishes and indicate your color selections on the Approval Selection Section on this page. ❑ Please confirm entrance wall thickness and type on the Approval Selection Section on this page. ❑ Please confirm the Main landing for Firefighters' Recall service (Phase -1 Recall) on Approval Selection Section on this page. ❑ Please confirm or correct the building power shown in the "Power Confirmation" section of the Approval Selection Section 7 Completed and signed Material Release Form. This form is provided by the Local ThyssenKrupp Elevator Representative. Any /ALL previously quoted manufacturing lead times for material delivery, shall begin the date of receipt by ThyssenKrupp of ALL approvals, confirmations, and a fully excuted subcontract agreement. The installation start date cannot be any earlier than the delivery of the material to the site and the completion of all items shown on the Pre - Installation Checklist sent to you in this submittal package. Approval Selection Section SECTIONS LABELED 1 -3 MUST BE COMPLETED nlsn selection: Elevator(s):1 �U=PUWIJLK(,0A1tD _ IUM PLEASE FILL OUT BLANKS FOR ITEMS "A -G" PLEASE NOTE THAT CHANGES TO ORIGINAL FINISH TLS = STAINLESS STEEL P = PLASTIC LAMINATE SELECTIONS OR FINISHES NOT INCLUDED IN THE TKE COLOR SELECTOR MAY RESULT IN A UP CHARGE. Rz ° BRONZE A. CAB WALL: FLAT STEEL WALLS (TKS) IF REVEALS ARE REQUIRED: IF BASE IS REQUIRED: B. CAB CEILING: DOWNLIGHT CEILING WITH HALOGEN LIGHTS C. CAB DOOR(S): FINISH:STEEL FINISH:( #4 STAINLESS STEEL) D. CAR SILL(S): ALUMINUM E. CAB FLOORING: BY OTHERS F. CAB HANDRAIL(S): 1, 1 1/2" CYLINDRICAL IF ADDITIONAL HANDRAIL(S): G. CAB PROTECTION: PAD BUTTONS PROVIDED CAB WALL FINISH: #4 STAINLESS STEEL CEILING FINISH: STEEL ( #4 STAINLESS STEEL) BINDER: FLOORING: FINISH FLOOR WEIGHT = 150 LBS. HANDRAIL(S) FINISH: #4 STAINLESS STEEL HANDRAIL(S) FINISH: Approval: Date: J #2 Power Confirmation: Elevator(s): 1 PLEASE FILL OUT ITEM "A" BELOW Controller: 208 VOLTS A.C., 3 PHASE, 60 CYCLES Starting Type: SOLID STATE STARTING Lighting Supply: 120 VOLTS A.C., 15 AMPS Raseri nn thiG infnrmatinn_ we reniiire elarfriral faariarc anri fiicari dicrnnnarfc ci71-d ner tha fnllnwinn infnrmafinn- Power Feeder Elevator Designation Motor Horsepower Starting A.C. Amps Total (Full Load Motor) A.C. Amps Rated A.C.Amps Short Circuit Current Ratings (At 600v Or Less) 1 20 195 95 65.1 5,000 AMPS Branch circuit conductor sizing, materials, and insulation (including branch circuit overcurrent protective device) to comply with all local electrical codes. Starting current with a max. allowable voltage drop of 10 %. Full load current and Rated current with a max. allowable voltage drop of 5 %. • The starting current is adjustable from 2 to 4.5 times the motor rated A.C. Amps. • The starting current of 3 times the motor rated A.C. Amps is nominal starting current value. NOTE: Also, a fourth wire of same size as three phrase wires is required for grounding purpose to minimize electrical noise interference. The grounding wire must be connected to the building electrical system ground. General Contractor must forward power requirements to the Electrical Contractor. A. WE REQUEST THAT THIS INFORMATION BE CONFIRMED BY THE ELECTRICAL CONTRACTOR. PLEASE CHECK THE BOX BELOW THAT APPLIES. IF THE IS DIFFERENT THAN SHOWN ABOVE, PLEASE BE SURE TO FILL IN CORRECT VOLTAGE. • Confirmed Power shown above. • Corrected Power Supply (AC) Volts: Phase Cycles: 3 Wire + Ground Is operation on emergency power source (by others) required? YES or NO (Please circle one). If yes, how many elevators will be capable of running at the same time while on emergency power? Approval: Date: Entrance Confi 1 PLEASE FILL OUT ITEMS "A -F" PLEASE NOTE THAT CHANGES TO ORIGINAL FINISH SELECTIONS OR FINISHES NOT INCLUDED IN THE TKE COLOR SELECTOR MAY RESULT IN A UP CHARGE. FLOOR A. Hoistway Entrance Frame Finish Color and Location: @1,2 STLS B. Hoistway Door Finish Color and Location: @1,2 STLS C. Hoistway Wall Type/ Construction and Location: I @1,2 D. Hoistway Finish Wall Thickness ( "X ") and Location: @1,2 E. Floor Designations: F. Provide Fire Fighters Recall: Approval 1,2 MAIN EGRESS ALT: LEVEL: and Finish Selections: Entrance Wall Detail W::, Elevator Entrance Frame „x„ FINISH MASONRY WALL TYPE FRAME „x Elevator Entrance Frame „ : r COMBINATION DRYWALL /MASONRY WALL FRAME Elevator Entrance Frame I ° DRYWALL TYPE FRAME * X = Wall thickness PC = POWDER COATED STLS = STAINLESS STEEL BRZ = BRONZE ALMN = ALUMINIUM Date: